I went on a good stretch last year and into this year of using WLP002, a solid English strain, in almost every hop forward beer I made. I’m pretty sure I started using the strain after hearing that Firestone Walker used WLP002 in all their hoppy beers during a podcast. Since then, I have brewed 25 batches with the strain, which seems like enough of a sample size to play with the data a little to see if anything stands out. I decided to focus on the finishing gravity of all the batches and correlate different brewing processes to this figure to explore what factors were influencing the final gravity of WLP002 fermented batches the greatest/least.

I’m not trying to blow anyone’s homebrewing mind with the data (which you’ll see is fairly predictable), I just like taking a step back every once in a while and look at some figures to see if my processes are working in a way I’m intending. There were a couple interesting points I found from this exercise like:

  • Mash temperatures at and above 155F started to reliably produced beers with gravities above 1.010, which is how I ended up preferring this strain in hoppy beers. To my palate, I preferred the beers with a little residual sweetness left in the beer which seemed to enhance the mouthfeel a little as well as hide the alcohol warming I got from some of the beers that finished lower.
  • The yeast generation and number of days each generation was stored in a mason jar unwashed in the fridge had very little impact on how WLP002 performed. I can feel confident now that simply swirling the yeast cake around with the little beer left in the fermenter after racking into a keg and pouring the mix of beer and yeast into a sanitized mason jar is a good way to keep the generations going. I typically would fill 3 jars with each batch I harvested yeast from and use 1 jar to ferment a future 5 gallon batch (many times without a starter).
  • Although there was a trend line showing higher finishing gravities when the initial fermentation temperature was near its final fermentation temperature, it was very slight. Basically, with enough time WLP002 would ferment out even if the temperature remained the same during fermentation. In fact, I had four batches that finished below 1.010 and never saw a rise in fermentation temperature. I would say that ramping the temperature did seem to speed up the process, but I don’t have any collected numbers to prove that.

Results – Below is a chart showing a few of the brewing processes I collected for each batch correlated to the finishing gravities. Keep in mind that a correlation coefficient of 0 means there is no relationship and anything at or below .30 would typically be considered a weak relationship and anything at or below .50 is a moderate relationship. Below this chart is a short blurb and chart of each of the brewing processes figures explained.

Results in Order:

  1. Mash temperature (moderate relationship)
  2. Original gravity (weak relationship)
  3. Ounces of slurry used (very weak relationship)
  4. Yeast generation (very weak relationship)
  5. Ramping fermentation temperature (very weak relationship)
  6. Slurry age (days) (very weak relationship)

FG Correlations ChartMash Temperature – I’m sure this won’t come as a shock to many, but the brewing processes with the highest correlation to the final gravity of each batch fermented with WLP002 was the mash temperature (Correlation Coefficient = 0.504). The chart below shows that this suggests the higher the mash temperature, the higher the finishing gravity tended to be. This wasn’t always the case, as you can see a handful of beers with mash temperatures around 154 that finished rather low. Most interesting in this graph to me is that I started to see more consistent higher final gravities when my mash temperature was at or above 155F.

Mash Temperature to Final Gravity

Yeast Generation – The yeast generation didn’t appear to have much of an impact on the final gravity of the batches (Correlation Coefficient = 0.140). This could suggest that harvested yeast if pitched in appropriate amounts seems to chomp up sugars at the same rate as the fresh vials did. In this case, over the 25 batches the average beer was fermented with 3.88 generation of slurry (ranging up to one batch fermented with 8th generation batch).

Final Gravity to Yeast Generation

Yeast Age (Days) – The number of days the slurry sat in a mason jar unwashed in my fridge also didn’t have an impact on the final gravity of each batch (Correlation Coefficient = 0.096). As you can see from the chart, even those beers fermented with slurry over 100 days old fermented out just fine. As a side note, for 10 of the batches I didn’t even make a yeast starter prior to being pitched with the average slurry pitched without a starter at 53 days old. If anything, I can say WLP002 is a workhorse, fermenting strongly no matter how I prepped or stored it!

Yeast Slurry Age to Final Gravity

Original Gravity – The original gravity had the second highest correlation to the final gravity of each batch (Correlation Coefficient = 0.386). This isn’t likely a surprise because as the gravity increases and the workload on the yeast increases, the more sugars WLP002 left behind. The chart below shows that in my experience it if wasn’t for 3 outlying batches, this correlation number would have came down.  Of the 25 batches fermented with WLP002, the average final gravity was 1.011. 

Final Gravity to Original Gravity

Ounces of Slurry Used – The ounces of slurry pitched into each batch had a minimal correlation (Correlation Coefficient = 0.199). I don’t actually measure each batches slurry amount, I eyeball the amount of slurry sitting in the mason jar that’s compacted below the liquid and use the markings on the mason jar as a gauge. This chart seems to tell me that as long as I’m pitching at and above 2.5 ounces of WLP002 with normal gravity beers, I’m fine (even without a starter). I should say again that I’m not washing the slurry, so the amount of actual yeast is less than the ounces I have indicated because they are mixed with trub from previous batches. I do my best to get very little trub into the fermenters after the boil because I know I will be harvesting the yeast. I typically get the cooled wort going in a good whirlpool then do a 30 min rest to let it settle. I then start emptying the wort from a side pickup discarding the first couple pints or so because this is where I see most of the trub that settled to the bottom coming out of the valve.

Final Gravity to Ounces of Slurry

Fermentation Temperature Changes – There was a very slight negative correlation of temperatures post yeast pitch and final gravities (Correlation Coefficient = -0.099). I subtracted the end of fermentation temperature of each batch by the yeast pitching temperatures to get a number of degrees difference for each batch. The chart below shows a slight decrease in attenuation when final fermentation temperature was closest to the pitch temperature or the more the fermentation was raised the greater the attenuation, but again this correlation was so low it’s not a convincing number. Given enough time WLP002 fermented out just fine even at consistent temperatures.

FG to Fermentation Temperature

Check Out My Book!


The New IPA: Scientific Guide to Hop Aroma and Flavor

In the NEW IPA, Scott Janish scours through hundreds of academic studies, collecting and translating the relevant hop science into one easily digestible book. Through experiments, lab tests, discussions with researchers, and interviews with renowned and award-winning commercial brewers, the NEW IPA will get you to think differently about brewing processes and ingredient selection that define today's hop-forward beers. It's a must-have book for those that love to brew hoppy hazy beer and a scientific guide for those who want to push the limits of hop flavor and aroma!

Available in paperback, ebook, and audiobook on Amazon! Also available in iTunes and the Google Play Book Store!

Connect on Social! 

Instagram
Facebook
Twitter

 

Subscribe to Blog Posts Below! 

You have Successfully Subscribed!